Alliance Doc

Abaqus/en: Difference between revisions

Page Discussion

Abaqus/en (view source)

Revision as of 19:46, 21 February 2023

359 bytes removed ,  1 year ago
Updating to match new version of source page
(Updating to match new version of source page)
(Updating to match new version of source page)
Line 59: Line 59:
   mp_mode=threads memory="$((${SLURM_MEM_PER_NODE}-3072))MB"
   mp_mode=threads memory="$((${SLURM_MEM_PER_NODE}-3072))MB"
}}
}}
To write restart date every N=12 time increments and at the end of each step of the analysis:
To write restart data every N=12 time increments specify in the input file:
  *RESTART, WRITE, FREQUENCY=12
  *RESTART, WRITE, OVERLAY, FREQUENCY=12
To disable writing restart data (into res,mdl,stt files) instead specify:
To write restart data for a total of 12 time increments specify instead:
  *RESTART, WRITE, FREQUENCY=0
  *RESTART, WRITE, OVERLAY, NUMBER INTERVAL=12, TIME MARKS=NO
To check the completed restart information do:
To check for completed restart information do:
  egrep -i "step|start" testsp*.com testsp*.msg testsp*.sta
  egrep -i "step|start" testsp*.com testsp*.msg testsp*.sta
Some simulations may benefit by adding the following to the Abaqus command at the bottom of the script:
Some simulations may benefit by adding the following to the Abaqus command at the bottom of the script:
Line 92: Line 92:
   mp_mode=threads memory="$((${SLURM_MEM_PER_NODE}-3072))MB"
   mp_mode=threads memory="$((${SLURM_MEM_PER_NODE}-3072))MB"
}}
}}
To read input file, input file should contain:
The restart input file should contain:
*HEADING
  *RESTART, READ
  *RESTART, READ
</tab>
</tab>
Line 128: Line 129:
cp -f * $SLURM_SUBMIT_DIR
cp -f * $SLURM_SUBMIT_DIR
}}
}}
To write restart date every N=12 time increments and at the end of each step of the analysis:
To write restart data every N=12 time increments specify in the input file:
  *RESTART, WRITE, FREQUENCY=12
  *RESTART, WRITE, OVERLAY, FREQUENCY=12
To disable writing restart data (into res,mdl,stt files) instead specify:
To write restart data for a total of 12 time increments specify instead:
  *RESTART, WRITE, FREQUENCY=0
  *RESTART, WRITE, OVERLAY, NUMBER INTERVAL=12, TIME MARKS=NO
To check the completed restart information do:
To check the completed restart information do:
  egrep -i "step|start" testst*.com testst*.msg testst*.sta
  egrep -i "step|start" testst*.com testst*.msg testst*.sta
Line 169: Line 170:
cp -f testst2* $SLURM_SUBMIT_DIR
cp -f testst2* $SLURM_SUBMIT_DIR
}}
}}
To read restart file, input file should contain:
The restart input file should contain:
*HEADING
  *RESTART, READ
  *RESTART, READ
</tab>
</tab>
Line 242: Line 244:
   mp_mode=threads memory="$((${SLURM_MEM_PER_NODE}-3072))MB"
   mp_mode=threads memory="$((${SLURM_MEM_PER_NODE}-3072))MB"
}}
}}
To write restart output at n=12 time intervals (at the beginning of the step and at increments ending immediately after each time interval) your input file should contain:
To write restart data for a total of 12 time increments specify in the input file:
  *RESTART, WRITE, OVERLAY, NUMBER INTERVAL=12, TIME MARKS=NO
  *RESTART, WRITE, OVERLAY, NUMBER INTERVAL=12, TIME MARKS=NO
To disable writing restart output (into the abq and sta files) instead specify:
Check for completed restart information in relevant output files:
*RESTART, WRITE, NUMBER INTERVAL=0
To check the completed restart information do:
  egrep -i "step|restart" testep*.com testep*.msg testep*.sta
  egrep -i "step|restart" testep*.com testep*.msg testep*.sta
</tab>
</tab>
Line 270: Line 270:
rm -f testep2* testep1.lck
rm -f testep2* testep1.lck
for f in testep1*; do [[ -f ${f} ]] && cp -a "$f" "testep2${f#testep1}"; done
for f in testep1*; do [[ -f ${f} ]] && cp -a "$f" "testep2${f#testep1}"; done
abaqus job=testep2 oldjob=testep1 input=myexp-sim-restart.inp recover \
abaqus job=testep2 input=myexp-sim.inp recover \
   scratch=$SCRATCH cpus=$SLURM_CPUS_ON_NODE interactive \
   scratch=$SCRATCH cpus=$SLURM_CPUS_ON_NODE interactive \
   mp_mode=threads memory="$((${SLURM_MEM_PER_NODE}-3072))MB"
   mp_mode=threads memory="$((${SLURM_MEM_PER_NODE}-3072))MB"
Line 309: Line 309:
cp -f * $SLURM_SUBMIT_DIR
cp -f * $SLURM_SUBMIT_DIR
}}
}}
To write restart output at n=12 time intervals (at the beginning of the step and at increments ending immediately after each time interval) your input file should contain:
To write restart data for a total of 12 time increments specify in the input file:
  *RESTART, WRITE, OVERLAY, NUMBER INTERVAL=12, TIME MARKS=NO
  *RESTART, WRITE, OVERLAY, NUMBER INTERVAL=12, TIME MARKS=NO
To disable writing restart output (into the abq and sta files) instead specify:
Check for completed restart information in relevant output files:
*RESTART, WRITE, NUMBER INTERVAL=0
To check the completed restart information do:
  egrep -i "step|restart" testet*.com testet*.msg testet*.sta
  egrep -i "step|restart" testet*.com testet*.msg testet*.sta
</tab>
</tab>
Line 344: Line 342:
done &
done &
WPID=$!
WPID=$!
abaqus job=testet2 input=$SLURM_SUBMIT_DIR/myexp-sim-restart.inp recover \
abaqus job=testet2 input=$SLURM_SUBMIT_DIR/myexp-sim.inp recover \
   scratch=$SCRATCH cpus=$SLURM_CPUS_ON_NODE interactive \
   scratch=$SCRATCH cpus=$SLURM_CPUS_ON_NODE interactive \
   mp_mode=threads memory="$((${SLURM_MEM_PER_NODE}-3072))MB"
   mp_mode=threads memory="$((${SLURM_MEM_PER_NODE}-3072))MB"
FuzzyBot
Bots
38,757

edits

Retrieved from "https://docs.alliancecan.ca/wiki/Special:MobileDiff/129671"